Altec TTP-343 Series Bedienungsanleitung Seite 1

USER’S MANUAL TTP-384M THERMAL TRANSFER / DIRECT THERMAL BAR CODE PRINTER

7 2.2.3 Rear View 1. Fan-fold paper entrance chute 2. Centronics interface 3. USB interface 4. RS-232C interface 5. Power jack socket *6. SD ca

8 V1.0, V1.1 microSD 256 MB Transcend, Panasonic V1.0, V1.1 microSD 512 MB Panasonic V1.0, V1.1 microSD 1 GB Transcend, Panasonic V2.0 SDHC CLASS 4

9 2.3 Operator Controls 2.3.1 Front Panel Display 2.3.2 LED Indicators LED Status Indication Off Printer power off On Printer power on On Pri

10 2.3.3 Front Panel Keys Keys Function 1. Enter the menu system 2. Once in the menu system, return to previous menu. If at menu root, exits the m

11 2.5 Loading Ribbon 1. Lift printer cover open. 2. Push the print head release lever to open the print head mechanism. 3. Install the ribbon o

12 5. Thread the ribbon through the ribbon sensor slot and print head. 5. Stick ribbon onto ribbon rewind paper core, keeping the ribbon flat and

13 Note: Please refer to videos on TSC YouTube or driver CD.  Loading path for ribbon

14 2.6 Loading Media 1. Lift printer cover open. 2. Push the print head release lever to open the print head mechanism. 3. Remove ONE label roll g

15 Note: Make sure the media is set at the center of spindle. Follow these steps: Make sure the width of the label. The space is reserved for

16 Install the label and make sure the label roll guard position of each sides are the same as the length of the label. Please check the outsi

i Contents 1. Introduction ... 1 1.1 Product Introduction ...

17 9. Using the front display panel, set media sensor type and calibrate the selected sensor. Note: * Re-calibrate the gap/black-mark sensors w

18 3. Menu Function Main Menu Overview RussianPolishSpanishExit↓↓↓Main MenuSetupFile ManagerDiagnosticsLanguageServiceExit↓↓↓↓↓Printer SetupFile L

19 3.1 Setup Menu Overview Exit↓Stop Bit(s)Exit↓ExitData Bits↓↓↓ExitCalibrationParityConfigure↓↓↓↓ZPL2StatusBaud RateStatus↓↓↓SetupExitSensorSerial

20 3.1.1 Printer Setup Printer SetupSpeedDensityDirectionPrint ModeOffsetShift YReference XCode PageCountry+000~-000TSPL2↓Exit↓↓↓↓↓Shift XReference

21 3.1.1.1 Speed: Use this option to setup print speed. The available print speed is between 4~12 ips and each increament/decreament is 1 ips.

22 key to enable the setting. Press key to cancel the setting and return to the previous menu. The following 2 figures are the printouts of DIR

23 Note: If printing from enclosed software/driver, the software/driver will send out the command, which will overwrite the setting set from the fro

24 This option is used to set the origin of printer coordinate system horizontally and vertically. Press the button to move the cursor from left

25 Windows Code Page (SBCS) Windows Code Page (DBCS) code page number International Character Set code page number International Character Set 125

26 Code Country Code Country Code Country Code Country 001 USA 034 Spanish (Spain) 044 United Kingdom 055 Brazil 002 Canadian-French 036 Hungarian

ii 4.1 Start the Diagnostic Tool ... 51 4.2 Printer Function (Calibrate sensor,

27 3.1.2 Sensor ExitStatusCalibrationSensor 3.1.2.1 Status This function is available to check the printer’s sensor status. When enter the [Status]

28 A. Gap Mode Press the and buttons to scroll the cursor to the media type and press the button to enter the sensor calibration mode.

29 Gap Size 0024 dot 2. Press the button to move the cursor from left digit to right digit, and press the button to set the value from “0”

30 printer. Gap Mode Pre-Printed 3. Then, printer will feed labels to calibrate the sensor sensitivity automatically. When calibration is comp

31 B. Bline Mode Press the and buttons to scroll the cursor to the sensor type. Press the button to enter the black-mark sensor c

32 Bline Mode Scan Mark Intensity x Ref. Level xxx 3. Open the printhead mechanism, put the black-mark under the media sensor. Pr

33 Bline Mode Pre-Printed 3. Then, printer will feed labels to calibrate the sensor sensitivity automatically. When calibration is completed,

34 C. Cont. Mode Press the and buttons to scroll the cursor to the sensor type. Press the button to enter the black-mark sensor c

35 Cont. Mode Complete Intensity x Ref. Level xxx 3. The sensor calibration is complete. Press the button the LCD screen will

36 3.1.3.1 Baud Rate Serial Comm. 1/5 > Baud Rate Parity Data Bits This option is used to set the RS-232 baud rate. The default setting i

1. Introduction 1.1 Product Introduction Thank you very much for purchasing TSC bar code printer. This printer is designed with die-casting aluminu

37

38 3.1.3.4 Stop Bit(s): Serial Comm. 4/5 Parity Data Bits > Stop Bit(s) This option is used to set the RS-232 Stop Bits. The default sett

39 3.1.4 Ethernet Use this menu to configure internal Ethernet configuration check the printer’s Ethernet module status, and reset the Ethernet mod

40 3.1.4.1.2 MAC Ethernet 1/3 > Status Configure Exit The MAC address information will be shown on the LCD display. Please press o

41 3.1.4.2.2 Static IP Use this menu to set the printer's IP address, subnet mask and gateway. Ethernet 2/3 Status > Configure

42 3.2 File Manager This feature is used to check the printer available memory and file list. ExitExit↓↓CARDCARD↓↓FLASHFLASH↓↓DRAMDRAMExit↓↓File Ma

43 File Manager 2/4 Avail. Memory File List DRAM: 256 KB > Avail. Memory FALSH: 6656 KB Del. All Files CAR

44 3.3 Diagnostics DiagnosticsExitPrint Config.Dump ModeRotate Cutter 3.3.1 Print Config. This feature is used to print current printer configurati

45 Self-test printout (with printer firmware V7.0 and later version) Model name F/W version Firmware checksum Printer S/N TSC configuration file

46 Numbers of download files Total & available memory space Print head check pattern

2 IEC60950-1: 2001 EN 60950-1/A11:2004 Wichtige Sicherheits-Hinweise 1. Bitte lesen Sie diese Hinweis sorgfältig durch. 2. Heben Sie diese Anleitung

47 3.3.2 Dump Mode Captures the data from the communications port and prints out the data received by printer. In the dump mode, all characters will

48 3.3.3 Rotate Cutter In case paper is jammed in the cutter, this feature can rotate the cutter blade forward or reverse direction, which is helpf

49 3.5 Service ServiceInitializationMileage Info.Exit This feature is used to restore printer settings to defaults and display printer mileage info

50 sensitivity Bline sensor sensitivity 2 (Will be reset. Need to re-calibrate the gap) Language English IP address DHCP 3.5.2 Mileage Info. Use t

51 4. Diagnostic Tool The Diagnostic Utility toolbox allows users to explore and change printer status and settings. Download graphics, fonts, firmw

52 4.2 Printer Function (Calibrate sensor, Ethernet setup, RTC setup………) 1. Select the PC interface connected with bar code printer. 2. Click the “

53 5 Setting Ethernet by Diagnostic Utility The Diagnostic Utility is enclosed in the CD disk \Utilities directory. Users can use Diagnostic Tool t

54 5.2 Using RS-232 interface to setup Ethernet interface 1. Connect the computer and the printer with a RS-232 cable. 2. Turn on the printer power.

55 5.3 Using Ethernet interface to setup Ethernet interface 1. Connect the computer and the printer to the LAN. 2. Turn on the printer power. 3. St

56 address, click “Static IP” radio button then enter the IP address, subnet mask and gateway. Click “Set IP” to take effect the settings. Users ca

3 바라며, 만약 잘못 판매 또는 구입하였을 때에는 가정용으로 교환하시기 바랍니다.

57 6. Troubleshooting 6.1 Common Problems The following guide lists the most common problems that may be encountered when operating this bar code

58 Not Printing * Cable is not well connected to serial or USB interface or parallel port. * The serial port cable pin configuration is not pin to p

59 Poor Print Quality * Ribbon and media is loaded incorrectly * Dust or adhesive accumulation on the printhead. * Print density is not set properly

60 Wrinkle Problem * Printhead pressure is incorrect. * Ribbon installation is incorrect. * Media installation is incorrect. * Print density is inco

61 6.2 Mechanism Fine Adjustment to Avoid Ribbon Wrinkles This printer has been fully tested before delivery. There should be no ribbon wrinkle pre

62 Adjust the print head pressure adjustment knobs The print head pressure adjustment knob has 5 levels of settings. Clockwise direction adjust

63 7. Maintenance This session presents the clean tools and methods to maintain your printer. 1. Please use one of following material to clean t

64  Please use 100% Ethenol. DO NOT use medical alcohol, which may damage the printer head.  Regularly clean the printhead and supply sensors on

65 Revise History Date Content Editor 2008/12/17 Revise troubleshooting section Camille 2009/3/4 Revise 2.1 section (Add ribbon take up paper core)

66 Corporate Headquarters Li Ze Plant 9F., No.95, Minquan Rd., Xindian Dist., No.35, Sec. 2, Ligong 1st

4 2. Operations Overview 2.1 Unpacking and Inspection This printer has been specially packaged to withstand damage during shipping. Please carefu

5 2.2 Printer Overview 2.2.1 Front View 1. LED indicators 2. LCD display 3. Front panel buttons 4. Paper exit chute 5. Printer cover 6. Cutter

6 2.2.2 Interior view 1. Ribbon rewind spindle 2. Print head 3. Ribbon sensor 4. Media sensor 5. Platen roller 6. Print head release lever 7. R